Blog
Lexmark Printer Paper Jam? Step-by-Step Fix Guide
A Lexmark printer paper jam can stop printing completely, trigger an error message, or leave a small piece of paper trapped somewhere inside the printer. Even when the visible sheet has been removed, the printer may continue reporting a jam if a torn piece remains in the paper path.
Paper jams can happen because of incorrectly loaded paper, damaged sheets, an overloaded tray, incorrect paper settings, worn rollers, or paper remaining inside the printer.
The safest approach is to stop the print job, remove the paper carefully, inspect the entire paper path, and then restart the printer.
Quick Fix: How Do You Clear a Paper Jam in a Lexmark Printer?
Start with these steps:
Stop or cancel the current print job.
Turn off the Lexmark printer if required by the model.
Remove loose paper from the input tray.
Open the printer’s access areas.
Locate the jammed sheet.
Pull the paper slowly in the direction of normal paper travel when possible.
Check for torn pieces.
Close all covers securely.
Reload paper correctly.
Turn the printer back on and test it
The Solution:
Do not forcefully pull a jammed sheet or use sharp objects to remove paper. A torn piece left inside the printer can cause repeated jams. If the printer continues displaying a paper-jam message after the visible paper has been removed, inspect the internal paper path and all accessible doors again.
Table of Contents
- 1. Stop the Print Job
- 2. Turn Off the Lexmark Printer
- 3. Remove Paper From the Input Tray
- 4. Open the Printer’s Access Doors
- 5. Locate the Jammed Paper
- 6. Pull the Paper Slowly
- 7. Check for Torn Paper
- 8. Check the Duplex Paper Path
- 9. Check the Rear Paper Path
- 10. Close Every Cover Securely
- 11. Reload Paper Correctly
- 12. Check the Paper Size and Type
- 13. Restart the Lexmark Printer
- 14. Check the Paper for Damage or Moisture
- 15. Check the Paper Tray and Guides
- Lexmark Printer Says Paper Jam but No Paper Is Visible
- Lexmark Printer Paper Jam Keeps Happening
- Lexmark Printer Paper Jam After Replacing Toner
- Lexmark Printer Paper Jam in the Duplex Unit
- Lexmark Printer Paper Jam Near the Output Tray
- Lexmark Printer Paper Jam During Startup
- How to Prevent Lexmark Printer Paper Jams
- When a Lexmark Paper Jam Requires Service
- Quick Lexmark Paper Jam Checklist
- Frequently Asked Questions
- Related Guides
- Final Thoughts
1. Stop the Print Job
If the printer begins making unusual noises or reports a paper jam, stop sending additional documents.
Cancel the current print job from your computer if possible.
Sending multiple documents while a jam is present can add more pages to the print queue and make troubleshooting more difficult.
If several documents are already waiting, clear the queue before testing the printer again.
For queue problems, see Lexmark Printer Print Queue Stuck? Clear Jobs & Fix Spooler.
2. Turn Off the Lexmark Printer
Before reaching inside the printer, follow the shutdown procedure recommended for your Lexmark model.
Turn the printer off and allow it to stop operating.
Some internal components, particularly in laser printers, can become hot during operation. Allow the printer to cool before accessing areas near the fuser or other heat-producing components.
Do not reach into areas that the manufacturer identifies as requiring professional service.
3. Remove Paper From the Input Tray
Start with the easiest area to inspect.
Remove the paper from the input tray and check whether the jammed sheet is visible.
Look for:
- Folded sheets
- Torn paper
- Multiple sheets stuck together
- Paper loaded incorrectly
- Paper caught near the tray entrance
Remove loose sheets carefully.
Do not overload the tray when reloading it later.
4. Open the Printer’s Access Doors
Lexmark printers may provide several access points for clearing paper jams.
Depending on the model, inspect areas such as:
- Front cover
- Rear access door
- Toner or cartridge area
- Duplex unit
- Output path
- Manual feed area
- Paper tray area
The exact locations vary by model.
Open only the panels intended for user access and follow the instructions displayed on the printer.
5. Locate the Jammed Paper
Look through the accessible paper path before pulling anything.
Try to identify where the sheet is trapped.
Common locations include:
- Input tray
- Inside the printer
- Around the cartridge area
- Rear paper path
- Duplex path
- Output area
If you can see the entire sheet, remove it carefully.
If only part of the paper is visible, check whether another access panel provides a safer route for removal.
6. Pull the Paper Slowly
When possible, remove the jammed sheet in the direction the paper normally travels through the printer.
Pull slowly and evenly.
Avoid sudden force because the paper can tear.
If the sheet starts tearing, stop and inspect the remaining section.
A small paper fragment can be enough to keep the printer’s paper sensor activated and cause another jam.
7. Check for Torn Paper
After removing the main sheet, inspect the paper path carefully.
Look for small fragments around:
- Rollers
- Corners
- Paper guides
- Rear access areas
- Duplex path
- Output area
Do not use sharp tools such as knives, screwdrivers, or scissors to scrape paper out of the printer.
If you cannot safely reach a fragment, follow the service instructions for your Lexmark model rather than forcing the component.
8. Check the Duplex Paper Path
If your Lexmark printer supports automatic two-sided printing, the duplex path is another common location for trapped paper.
Open the accessible duplex area and inspect it carefully.
Check for:
- Folded paper
- Torn sheets
- Multiple pages
- Small fragments
Make sure the duplex unit is properly closed after clearing the paper.
A partially closed duplex component can also prevent normal printing.
9. Check the Rear Paper Path
If the jam is not visible from the front, inspect the rear access area if your printer provides one.
Rear access doors often provide access to paper travelling through the printer.
Remove visible paper carefully.
If the paper is close to a hot internal component, allow the printer sufficient time to cool before accessing the area.
Do not force rollers or internal components.
10. Close Every Cover Securely
After removing the jam, close all access doors and covers completely.
The printer may continue reporting a paper jam or cover error if a door is not fully closed.
Check the printer display.
The status should return to Ready after the printer completes its startup or jam-clearing process.
If the error remains, turn the printer off and back on according to the normal operating procedure.
11. Reload Paper Correctly
Once the jam is cleared, reload the tray properly.
Use paper that is:
- Clean
- Dry
- Flat
- Undamaged
- Appropriate for the printer
Adjust the paper guides so they rest against the paper without pressing too tightly.
Do not fill the tray beyond its indicated capacity.
A tray that is overloaded or incorrectly adjusted can cause another jam.
12. Check the Paper Size and Type
Incorrect paper settings can contribute to feeding problems.
Check the printer and computer settings for the correct ones:
- Paper size
- Paper type
- Tray
- Orientation
For example, if the printer is configured for one paper size but another size is physically loaded, the printer may not feed the paper as expected.
Select the correct tray and paper settings before printing again.
13. Restart the Lexmark Printer
After clearing the jam and closing the covers, restart the printer.
Allow it to complete its startup process.
Check that the paper-jam message has disappeared.
Then print a small test document rather than immediately sending a large print job.
If the test page prints normally, the jam has likely been resolved.
14. Check the Paper for Damage or Moisture
If jams keep happening, inspect the paper itself.
Paper that is bent, curled, damp, wrinkled, or damaged can feed incorrectly.
Avoid mixing different paper types or sizes in the same tray unless your printer specifically supports it.
Store unused paper in a dry environment and keep it protected from moisture.
Using clean, flat paper can significantly reduce recurring feed problems.
15. Check the Paper Tray and Guides
Incorrectly positioned paper guides can cause sheets to enter the printer at an angle.
Make sure the guides are aligned with the paper.
They should hold the paper securely without squeezing it.
Also inspect the tray for:
- Broken guides
- Damaged plastic
- Foreign objects
- Paper scraps
- Excessive paper dust
A damaged tray can contribute to repeated jams even when the paper itself is good.
Lexmark Printer Says Paper Jam but No Paper Is Visible
This is a common and frustrating situation.
If the printer reports a jam but you cannot see paper, a small fragment may be trapped inside the paper path.
Check all accessible areas, including:
- Rear access
- Duplex path
- Input area
- Output area
- Cartridge area
- Paper guides
Also check that every cover and tray is properly closed.
If the message remains after a complete inspection and restart, the printer may have a sensor or mechanical problem.
Lexmark Printer Paper Jam Keeps Happening
A recurring paper jam usually means something beyond a single sheet is causing the problem.
Check:
- Paper quality
- Paper size
- Paper loading
- Tray capacity
- Paper guides
- Rollers
- Duplex path
- Paper fragments
- Printer maintenance
If the same location jams repeatedly, note where the paper stops.
Repeated jams at the same point can indicate a feeding or mechanical issue.
Lexmark Printer Paper Jam After Replacing Toner
If the paper jam began after replacing toner, inspect the cartridge area.
Make sure the cartridge is seated correctly and that no packaging material was left inside the printer.
Check the paper path around the cartridge area for torn paper or foreign objects.
Do not force the cartridge or internal components into position.
If the printer also displays a toner or cartridge warning, see Lexmark Printer Toner Not Recognized? Easy Fix Guide.
Lexmark Printer Paper Jam in the Duplex Unit
If paper jams during two-sided printing but normal one-sided printing works, the duplex path deserves special attention.
Remove the paper from the accessible duplex area.
Check for folded or partially fed sheets.
Make sure the duplex unit is installed and closed correctly.
Then test a one-sided print.
If one-sided printing works but duplex printing repeatedly jams, the issue may be isolated to the duplex path or its settings.
Lexmark Printer Paper Jam Near the Output Tray
If paper stops near the output area, remove it slowly and carefully.
Check for torn fragments around the exit rollers.
Make sure the output area is not overloaded with printed pages.
A large stack of completed documents can interfere with output on some printer configurations.
Remove completed pages and test the printer again.
Lexmark Printer Paper Jam During Startup
If the printer reports a paper jam immediately after being turned on, inspect the paper path before sending a print job.
Look for a sheet that remained inside the printer from an earlier jam.
Also check whether a cover, tray, or duplex component is correctly positioned.
If the printer reports a jam with no paper present, the problem may involve a paper sensor or mechanical component.
How to Prevent Lexmark Printer Paper Jams
Preventing jams is easier than repeatedly clearing them.
Use the Correct Paper
Use paper recommended for your printer and avoid damaged or heavily curled sheets.
Do Not Overfill the Tray
Keep the paper level below the tray’s maximum indicator.
Adjust the Guides
Paper guides should hold the stack correctly without squeezing it.
Store Paper Properly
Keep paper dry, flat, and protected from excessive humidity.
Remove Torn Paper Completely
Never leave small pieces inside the printer after a jam.
Keep the Printer Clean
Paper dust and debris can affect feeding components.
Use the Correct Paper Settings
Select the correct size and type for the paper loaded in the tray.
When a Lexmark Paper Jam Requires Service
Most ordinary paper jams can be cleared by the user.
However, professional service may be appropriate if:
- The printer repeatedly jams in the same location.
- Rollers appear damaged.
- A paper fragment cannot be safely removed.
- The printer reports a jam with no visible paper.
- The error returns immediately after restarting.
- Internal components appear damaged.
- The printer makes unusual mechanical noises.
Avoid forcing internal parts or disassembling components that are not intended for user access.
Quick Lexmark Paper Jam Checklist
Before testing the printer again, confirm:
- The print job has been canceled.
- Printer has been safely stopped.
- Input tray is empty during inspection.
- Jammed paper has been removed.
- No torn paper remains.
- Rear paper path is clear.
- Duplex path is clear.
- Cartridge area is clear.
- All covers are closed.
- Paper is loaded correctly.
- Paper guides are aligned.
- Paper size is correct.
- Printer has been restarted.
- Jam message has disappeared.
Frequently Asked Questions
Why does my Lexmark printer keep saying paper jam?
The printer may still have paper or a small paper fragment inside the paper path. Incorrect paper loading, damaged paper, tray problems, rollers, or paper sensors can also cause repeated jam messages.
How do I clear a paper jam from a Lexmark printer?
Stop the printer, remove accessible paper carefully, inspect the complete accessible paper path, check the duplex and rear areas, close all covers, reload paper correctly, and restart the printer.
Why does my Lexmark printer say paper jam when there is no paper?
A small torn fragment may be hidden inside the printer, or a paper sensor may not have returned to its normal position.
Inspect all accessible paper paths carefully.
Can I pull jammed paper out of my Lexmark printer?
You can normally remove accessible paper carefully, but avoid using excessive force. Pull slowly and, when practical, in the direction of normal paper travel.
Why does my Lexmark printer jam during duplex printing?
A problem in the duplex paper path can cause jams during two-sided printing. Check the duplex unit for folded paper, fragments, or incorrectly positioned components.
Can bad paper cause Lexmark printer jams?
Yes. Damp, curled, wrinkled, damaged, or incorrectly sized paper can cause feeding problems.
What should I do if paper tears inside my Lexmark printer?
Stop and inspect the accessible paper path for remaining fragments. Do not use sharp objects to remove pieces. If a fragment is inaccessible, follow the printer’s service instructions or contact a qualified technician.
Related Guides
- Lexmark Printer Not Printing? 15 Proven Fixes That Actually Work (2026)
- Lexmark Printer in Error State? Quick Fix Guide
- Lexmark Printer Offline? 10 Fast Fixes to Get It Back Online (2026)
- Lexmark Printer Toner Not Recognized? Easy Fix Guide
- Lexmark Printer Print Queue Stuck? Clear Jobs & Fix Spooler
- Lexmark Printer Driver Unavailable? Fix Driver Problems Fast
- Lexmark Printer Connected But Not Printing? Fix It Fast
Final Thoughts
A Lexmark printer paper jam is usually caused by a sheet or paper fragment becoming trapped somewhere along the paper path. The key is to remove the paper carefully and inspect all accessible areas rather than simply pulling on the visible portion.
Check the input tray, cartridge area, rear path, output area, and duplex path. After clearing the jam, reload clean and correctly sized paper, adjust the guides, close every cover, and restart the printer.
If the same jam keeps returning, focus on the paper quality, tray alignment, rollers, duplex path, and possible mechanical or sensor problems. Repeated jams in the same location may require professional service.
