Uncategorized

Lexmark Printer in Error State? Quick Fix Guide

If your Lexmark printer is in an error state, it may stop printing even though the printer is powered on and connected to your computer. Windows may show an error message, the printer display may show a warning, or print jobs may remain stuck without producing a page.

An error state can be caused by something simple, such as a paper jam or empty tray, but it can also result from toner problems, connection failures, driver issues, a stuck print queue, or a hardware-related warning.

The fastest solution is to identify the exact condition preventing the printer from reaching Ready status. Start with the basic checks below before reinstalling drivers or changing network settings.

Quick Fix: Why Is My Lexmark Printer in an Error State?

Start with these checks:
Check the printer display for an error message.
Make sure paper is loaded correctly.
Check for paper jams.
Check toner or cartridge status.
Make sure all printer covers are closed.
Check the USB or WiFi connection.
Clear stuck print jobs.
Restart the printer and computer.
Check the printer driver.
Remove and re-add the printer if necessary

The Solution:

A Lexmark printer usually remains in an error state because the printer has detected a condition that prevents normal operation. Resolve the physical printer error first, then check the connection, print queue, and driver if the error remains.

Table of Contents

1. Check the Lexmark printer display

The printer’s display is usually the best place to start.

Look for the exact message shown by the printer.

Common messages can relate to:

  • Paper jams
  • No paper
  • Low or empty toner
  • Cartridge problems
  • Open covers
  • Network connection
  • Maintenance
  • Hardware problems

Write down or note the exact message before restarting the printer.

A specific error message can point directly to the affected component.

2. Check for a Paper Jam

A paper jam is one of the most common reasons a Lexmark printer enters an error state.

Inspect the accessible paper paths, including:

  • Input tray
  • Output area
  • Rear access
  • Cartridge area
  • Duplex path

Remove jammed paper carefully.

Check for small torn pieces as well. Even a small fragment can keep the printer’s paper sensor activated.

For detailed instructions, see Lexmark Printer Paper Jam? Step-by-Step Fix Guide.

After clearing the jam, close all covers securely and restart the printer.

3. Check the Paper Tray

If the printer does not detect paper correctly, it may remain in an error state.

Remove the paper from the tray and reload it neatly.

Make sure:

  • The paper is flat.
  • The paper is the correct size.
  • The tray is not overloaded.
  • The guides are positioned correctly.
  • No damaged sheets are present.

Check the printer display after reloading the paper.

If the printer returns to Ready status, send a small test document.

4. Check the Toner or Cartridge

A toner or cartridge problem can also prevent printing.

Check the printer display for messages related to:

  • Low toner
  • Empty toner
  • Cartridge not recognized
  • Cartridge not detected
  • Replace cartridge
  • Invalid cartridge

If you recently replaced a cartridge, make sure it is installed correctly and that all required protective materials have been removed.

If the printer does not recognize the toner, see Lexmark Printer Toner Not Recognized? Easy Fix Guide.

5. Make Sure All Covers Are Closed

Lexmark printers can enter an error state if an access door or cover is not completely closed.

Check:

  • Front cover
  • Rear cover
  • Toner access area
  • Paper tray
  • Duplex unit

Open and close the relevant panel carefully.

Do not force a cover into position.

If the printer immediately returns to the error state after all covers are closed, continue troubleshooting the displayed message.

6. Restart the Lexmark Printer

A restart can clear a temporary error condition.

Turn off the printer using its normal power control.

Wait several seconds.

Turn the printer back on and allow it to complete its startup sequence.

Do not send a print job until the printer has finished initializing.

If the display returns to Ready, print a test page.

If the same error returns immediately, focus on the specific error message rather than repeatedly restarting the printer.

7. Check the Printer Connection

If the printer itself appears normal but Windows shows an error state, the problem may involve communication between the printer and computer.

For USB connections, check the cable and USB port.

For WiFi printers, verify that:

  • The printer is connected to WiFi.
  • The computer is connected to the same network.
  • The printer has not switched to another network.
  • The router is functioning normally.

If the printer is offline, see Lexmark Printer Offline? 10 Fast Fixes to Get It Back Online (2026).

8. Clear the Print Queue

A stuck or corrupted print job can cause the printer to appear unavailable.

Open the Lexmark printer’s print queue and cancel pending documents.

Wait until the queue is empty.

Then send a simple test document.

If the queue cannot be cleared, restart the Windows Print Spooler.

A clean queue helps determine whether the error is caused by a specific print job or the printer itself.

9. Restart the Print Spooler

The Windows Print Spooler manages print jobs between your computer and printer.

If it becomes stuck, Windows may report a printer error even though the physical printer is ready.

Open Windows Services and locate Print Spooler.

Restart the service.

Then check the Lexmark printer again.

Try printing a test page after the queue has been cleared.

If the problem occurs repeatedly, investigate the printer driver and connection.

10. Check the Lexmark Printer Driver

A damaged or incompatible driver can prevent Windows from communicating correctly with the printer.

Driver problems may occur after:

  • Windows updates
  • Printer software changes
  • Moving the printer to another computer
  • Installing an incorrect driver
  • Removing printer software

If the printer display shows Ready but Windows continues to report an error, inspect the installed Lexmark driver.

Reinstall the correct driver for the exact printer model and operating system if necessary.

For more detailed troubleshooting, see Lexmark Printer Driver Unavailable? Fix Driver Problems Fast.

11. Check Whether the Printer Is Offline

An offline printer can sometimes appear as an error state in Windows.

Open your printer settings and check the current status.

Make sure the printer has not been placed into offline mode.

If the printer is connected by WiFi, confirm that it is still connected to the correct network.

If it is connected through USB, check the cable.

After restoring the connection, clear any old print jobs and send a test page.

Lexmark Printer Error State After a Paper Jam

If the error began after a paper jam, inspect the complete accessible paper path.

Do not stop after removing the main sheet.

Look for small pieces around:

  • Rollers
  • Paper guides
  • Rear access
  • Duplex path
  • Output area

Once the paper path is clear, close all covers and restart the printer.

If the error remains despite no visible paper, a paper sensor may still be detecting a problem or another mechanical issue may be present.

Lexmark Printer Error State After Replacing Toner

If the error appeared immediately after replacing the toner, check the new cartridge.

Make sure:

  • It is the correct cartridge.
  • It is installed in the correct position.
  • Protective packaging has been removed.
  • The cartridge is fully seated.
  • The printer recognises it.

A cartridge that is incompatible or incorrectly installed can prevent the printer from returning to Ready status.

See Lexmark Printer Toner Not Recognized? Easy Fix Guide for more troubleshooting.

Lexmark Printer Error State but No Error Message

Sometimes the printer may simply display an error status without explaining the cause clearly.

In this situation, check the basics:

  1. Paper.
  2. Paper jams.
  3. Toner.
  4. Cartridge.
  5. Covers.
  6. Network or USB connection.
  7. Print queue.
  8. Printer driver.

Restart the printer after completing the physical checks.

If the printer still shows an error state, check the printer’s configuration or status page if your model provides one.

Lexmark Printer Error State on Windows

If Windows reports the printer as being in an error state, first determine whether the printer itself shows an error.

If the printer display also shows an error

Focus on the physical printer.

Check paper, toner, cartridge, covers, and jams.

If the printer display says Ready

Focus on Windows.

Check:

  • Printer connection
  • Offline mode
  • Print queue
  • Print Spooler
  • Driver
  • Printer configuration

This distinction helps determine whether the problem is printer-side or computer-side.

Lexmark Printer Error State but Connected

A printer can be connected to WiFi or USB and still remain in an error state.

Connection only confirms that some communication is possible.

Check the printer’s actual status.

If it is showing an internal error, resolve that condition first.

If the printer says Ready but your computer reports an error, investigate the driver, spooler, and printer configuration.

For connection-specific problems, see Lexmark Printer Connected But Not Printing? Fix It Fast.

Lexmark Printer Error State After Windows Update

If the printer worked normally before a Windows update, the update may have affected the driver or printer configuration.

Restart the computer and printer first.

Then check:

  • Printer driver
  • Printer queue
  • Print Spooler
  • Printer status
  • Printer connection

If necessary, remove and reinstall the correct Lexmark printer driver.

After installation, restart Windows and print a test page.

Lexmark Printer Error State After Changing WiFi

Changing the router, WiFi password, or network name can make a previously configured printer unavailable.

Reconnect the Lexmark printer to the new WiFi network.

Then check whether the computer still has the correct printer entry.

If the printer’s network address changed, removing and re-adding the printer may be necessary.

For complete wireless setup instructions, see Lexmark Printer WiFi Setup Guide (Windows, Mac & Mobile).

Lexmark Printer Error State With Stuck Print Jobs

If the printer entered an error state while printing, the print queue may contain one or more failed jobs.

Cancel all pending documents.

Restart the Print Spooler if necessary.

Then restart the printer.

Send a small test document instead of immediately resubmitting the original job.

This helps prevent the same corrupted print job from triggering another error.

How to Identify the Source of a Lexmark Error

Use this simple process.

Printer display shows an error

Focus on paper, toner, cartridge, covers, hardware, or printer maintenance.

Printer says Ready but computer says Error

Focus on the driver, spooler, queue, and connection.

Printer is offline and shows no physical error

Focus on WiFi, USB, network settings, and printer configuration.

Printer enters error state after every print job

Focus on the document, driver, print queue, and communication.

Printer remains in error state immediately after startup

Focus on the printer’s internal condition and the exact message displayed.

Quick Lexmark Error State Checklist

Before contacting technical support, check:

  • Printer display
  • Paper supply
  • Paper jams
  • Paper fragments
  • Toner level
  • Cartridge installation
  • Cartridge recognition
  • Printer covers
  • WiFi connection
  • USB connection
  • Offline mode
  • Print queue
  • Print Spooler
  • Printer driver
  • Recent system updates
  • Recent network changes

Frequently Asked Questions

Why is my Lexmark printer in an error state?

A Lexmark printer can enter an error state because of a paper jam, empty tray, toner problem, cartridge error, open cover, connection issue, driver problem, stuck print queue, or hardware condition.

Check the printer display first.

How do I get my Lexmark printer out of error state?

Resolve any displayed printer error, check paper and toner, clear paper jams, close all covers, restart the printer, and verify the computer connection.

If the printer itself says Ready but Windows shows an error, check the queue, spooler, and driver.

Why does my Lexmark printer say error but have no visible problem?

A small paper fragment, cartridge issue, communication problem, or printer sensor condition may not be immediately visible.

Inspect all accessible areas and check the printer’s status information.

Why is my Lexmark printer in error state after replacing toner?

The toner cartridge may be incompatible, incorrectly installed, or not recognized.

Check the cartridge position and remove any protective packaging.

Why does Windows say my Lexmark printer is in an error state?

Windows may be unable to communicate with the printer because of a driver, print queue, spooler, USB, or network problem.

Check whether the printer itself shows Ready.

Can a paper jam cause a Lexmark printer error state?

Yes. A paper jam or even a small piece of torn paper can trigger an error condition and prevent printing.

Why is my Lexmark printer in error state after changing WiFi?

The printer may still be configured for the old network, or your computer may still be using an outdated printer configuration.

Reconnect the printer to the correct WiFi network and re-add it if necessary.

  • Lexmark Printer Not Printing? 15 Proven Fixes That Actually Work (2026)
  • Lexmark Printer Offline? 10 Fast Fixes to Get It Back Online (2026)
  • Lexmark Printer Driver Unavailable? Fix Driver Problems Fast
  • Lexmark Printer WiFi Setup Guide (Windows, Mac & Mobile)
  • Lexmark Printer Paper Jam? Step-by-Step Fix Guide
  • Lexmark Printer Connected But Not Printing? Fix It Fast
  • Lexmark Printer Print Queue Stuck? Clear Jobs & Fix Spooler
  • Lexmark Printer Toner Not Recognized? Easy Fix Guide

Final Thoughts

A Lexmark printer in error state does not necessarily indicate a serious hardware failure. In many cases, the cause is a paper jam, toner problem, incorrect cartridge installation, stuck print queue, connection issue, or driver problem.

Start with the printer’s own display and resolve any physical error first. Then check the paper, toner, covers, and connection. If the printer says Ready but your computer reports an error, focus on the print queue, Print Spooler, driver, and printer configuration.

Working through these checks in order makes it easier to identify the actual cause and restore your Lexmark printer to Ready status without unnecessary troubleshooting.

Leave a Reply

Your email address will not be published. Required fields are marked *